Tesco Internet Phone Siemens DP450 Unlocking

Guide to unlocking your Tesco Siemens DP450 IP Phone and use with VoiceHost.co.uk

Gigaset Communications have created a process that enables Tesco Internet Phone subscribers with Siemens Dual-Phone DP450 to unlock the phone from the Tesco Internet Phone service. This will enable the phone to be used with VoiceHost.
This is an approved method for unlocking the Siemens Dual-Phone DP450 defined and released by Gigaset Communications, the original supplier of the phone to Tesco.

If this procedure is not followed exactly your phone might not work any more. In this case, Gigaset Communications or VoiceHost cannot accept any warranty claims.

NOTE: The Tesco Internet IPA 1000 ATA was an IAX2 device, most VoIP providers are SIP only, including VoiceHost.

Unlock procedure
Your Phone should have the latest released Tesco software version, else this unlock procedure will not work.
On your handset:
BASE SETTINGS SOFTWARE UPDATE [OK]
→→
Select and press OK Enter the system PIN (0000) and press [OK]

The base station establishes a connection to the internet or a local PC.
[YES] Press the display key to start the firmware update. If no update is needed, this will be displayed.
To unlock the WEB interface of the DP450, you need to enter the following service code. Please use the exact code as is described below, else your phone will not work any more.

SETTINGS BASE

94762001
(Now "Eeprom" must be displayed)
Insert the following number sequence:
01778 06183 06191
Press OK to finish the programming.
"Saved" must be displayed on the Handset.
Then release the phone to be able to upgrade it with the latest Retail firmware version.
SETTING BASE

94762001
(Now "Eeprom" must be displayed)
Now insert this number sequence:
04850 04351 04864
Press [OK] to finish the programming. "Saved" must be displayed on the Handset.
After this procedure, you can upgrade your phone to use the latest retail firmware version.
SETTINGS BASE SOFTWARE UPGRADE
→→
Select and press Enter the system PIN (0000) and press [OK]
The base station establishes a connection to the internet or a local PC.
[YES] Press the display key to start the firmware update.
Please Note:
The firmware update can last up to 3 minutes.
Some people experience problems with the firmware upgrade where the process does not complete. If after 30 minutes your handset keeps flashing 'Base 1' you will need to power cycle your phone base by disconnecting the power for 10 minutes and then reconnect it.
Allow the phone to boot, we recommend leaving it a further 30 minutes to boot and upgrade. If your handset is still flashing 'Base 1' after this time, you will need to pair the handset to the base. To do this, follow the procedure below:

On your handset:
SETTINGS HANDSET REGISTER
→→
On your base:
Hold down the blue button for 30 seconds.
If all goes well, your handset should now be paired and you should be able to make a call.


Once your phone has been unlocked, you will be able to follow our standard set-up guide:

Siemens Gigaset - Wizard

The Siemens Gigaset phone can be configured to use the VoiceHost service in two ways, the first method is by using the built-in configuration wizard on the phone handset. When you connect your phone to your router and power for the first time the wizard will automatically start. To configure the phone, you will need your extension username and password. Please note, these are not the details you have to log in to the website. The required details can be located in the control panel under 'Extension Config'.

Follow the on-screen prompts, select VoiceHost and enter your extension username and password. Once you have finished answering the questions in the wizard you should be able to start making calls with VoiceHost. To test your configuration, try dialling 1234 to listen to the welcome message.

If you require more than one account/extension configured on your phone, or you are having problems accessing voicemail or IVR menus you will need to check your settings by running through the following procedures.

Web-Based Configuration

To access the web-based setup, you will need to determine the IP address of the phone. To do this you will need the handset. On the handset select 'menu > settings > base > network > IP address. The display will show you the current IP address of the phone.

Now you have obtained the IP address you can enter this address in a web browser to access the web configuration page.

Enter the default system pin of '0000' and click ok. Once logged in you will be shown a menu. Select the 'Settings' option and then 'Connections'. Select the first SIP Account 'Edit' button. You will be shown the following screen:

Please enter the following details into the fields provided:

- SIP:
Authentication Name: <extension username> See Control Panel for Details
Authentication Password: <extension password> See Control Panel for Details
Username: <extension username> See Control Panel for Details
Domain: See Control Panel for Details
Display Name: <your name>
Proxy server address: See Control Panel for Details
Proxy server port: See Control Panel for Details
Registrar server: See Control Panel for Details
Registrar server port: See Control Panel for Details

- Network:
STUN enabled: no
STUN server: See Control Panel for Details
STUN port: 5000
NAT refresh time: 20 seconds
Outbound proxy mode: Auto
Outbound proxy port: 5060

- Voice Codecs:
VoIP volume: Normal
Enable Annex B for G729: No
Selected codecs: G711 ulaw and alaw

Once the above details have been entered select the 'Set' button to save your settings.

To make sure that your 'touch tones' or DTMF will work correctly, select the 'Advanced Settings'. You will be shown the following screen:

Change the 'DTMF over VoIP Connections' to 'SIP Info' with all other options unticked. Click 'Set' to complete the setup process.

Once the phone registers, you will be able to start making calls.

Gigaset N300IP - N510IP - GO DECT Base station Configuration

Setting up the Gigaset N300IP, N510IP and GO DECT base stations

(handsets are simply paired to the base station)

Power up the N300IP, N510 or GO DECT Base station and connect a network cable into the side. Once the connection light comes on a steady blue then the device is powered up, connected to the network, and ready to use.

The base stations can have different Gigaset Model handsets paired to them, therefore, the handset model does not matter.

IP DECT Handsets for use with Gigaset Base Stations are:

  • Gigaset A510 DECT Handset
  • Gigaset S650H DECT Handset Pro
  • Gigaset R650H DECT Handset Pro
  • Gigaset CL750A GO - Sculpture DECT Handset
  • Gigaset SL450A DECT Handset
  • Gigaset S850A DECT Handset
Register the Handsets
  1. Connect the handsets to the power outlet and let them charge.
  2. When they first come on they will display the message “Please register”.
  3. To start the registration process you need to press the right hand navigation key .
  4. Once selected on the menu screen, use the navigation keys to move down to “Settings” and press “OK”
  5. On the settings menu move down to “Handset” and select “OK”
  6. On The Handset Menu select “Register H/Set” and press “OK”.
  7. This will then ask for the PIN which by default is “0000”
  8. The Handset will then display the Registering Procedure Screen.
  9. When this screen shows you will need to press the button on the base station for a minimum of 3 seconds.
  10. Once the handset is registered it may tell you that there is a message and ask you to update the firmware. This is OK to allow.
Setting up the Base Station and registering.
  1. Open a web browser and go to www.gigaset-config.com. This will search for your base station and display the IP address. This will then automatically re-direct you to the base station’s web page.
  2. On the login page enter the default PIN (0000) and press “OK”.
  3. The first time you log in you will get a security warning. Tick the tick box and click “OK”.
  4. After the security page you will be displayed with the main home page. On the Tabs at the top select the “Settings” tab.
The Settings Tab
Network > IP Configuration

If you need to set the base station with a static IP then set the IP Network details here, if it is OK to have it as DHCP then leave the settings on this page as they are. Please note that if you change to a static IP address then you will need to reload the web page.

Telephony > Connections
  1. On the connections menu you need to set all of the seats that you are assigning to the base station.
  2. The Seats you want to add are, by default, labelled IP1 - IP6.
  3. Next to the seat you wish to configure select “Edit”
  4. Once you have clicked “Edit” you will be presented with the configuration page for the Seat you want to add.
  5. The first thing to do is click on “Show Advanced Settings”
  6. Rename the connection to something more related to the account than IP1 .
  7. Enter in the Seat details from the control panel as the username and password. The Authentication name is the same as the username.
  8. Add in the name of the seat.
  9. Enter in the Domain, Proxy Server and Registration Server all as per the control panel
  10. Change the Registration Refresh Timer to “60”
  11. Once complete click on “Set” at the bottom. This will take you back to the “Connections” page. Please note the connection will say “Registration Failed”. If you have a live internet connection simply press F5 and you should see that this is now registered. If you do have a live internet connection but after a couple of refreshes over a couple of minutes, the connection is still showing “Registration Failed”, please go back over the settings above.
  12. Repeat the above step for each seat you wish to set up.
Telephony > Audio
  1. On the Audio tab click on “Show Advanced Settings”
  2. Under the heading for each seat that you have set up, set the audio codecs as: G711u law/G711a law/
  3. Once set click on the “Set” button at the bottom of the screen.
Telephony > Number Assignment
  1. Next to each handset that is registered you can name them. This name will be displayed on the handset.
  2. Select the Seats that you want this to be assigned to. You must un-tick all of the other connections for each.
  3. Each handset must be assigned to a different seat.
  4. Once you have completed this then press “Set” at the bottom of the page.
Telephony > Advanced VoIP settings
  1. Scroll to the bottom of this page and change “Use Random Ports” to “Yes” and then press “Set”.

Your Base Station and handsets should now be configured and working.

Avaya IP Office SIP trunk guide

How to configure Avaya IP Office SIP Trunking with VoiceHost

Below Version 8: Avaya IP Office software older than version 8 requires a STUN server for systems that do registration.

Navigate to System in the tree-view menu on the left of the PBX GUI

LAN Settings - Enter either the public IPv4 address of the broadband circuit or one that has been issued to you the customer to use. (STUN server details can be entered here)

IP Route - An IP Route will need to be created containing the IPv4 Address of the VoiceHost Proxy, giving the route to access the gateway connected to the LAN 2 port.

SIP registrar - These settings are normally left as default

SIP Line:

  • Create a new SIP Line and enter the VoiceHost FQDN as provided in your control panel.
  • Set the Transport setting as shown including DNS and ITSP Proxy Address unless supplied different information.
  • The SIP Credentials will need to be configured using the User Name and Password as supplied by VoiceHost and is also used for the Authentication Name and Contact.
  • The SIP URI settings only need two entries as shown. One is for the outgoing calls and the other a wild card entry for the incoming DDI calls which are routed to the Incoming Call Routes by their group number.

SIP URI settings for outgoing calls

  • Via is taken from the Use Network Topology Info setting on the Transport page.
  • Local URI is the CLI which needs to set to line, normally the site main number and needs to be entered using the E.164 format as shown +441234567890.
  • Contact, Display Name and PAI all need to be set as shown.
  • Registration is selected form the drop down box and is the SIP Credentials settings.
  • Incoming and Outgoing Group should be set to the same number as the SIP Line number.
  • Max Calls per Channel is the amount of concurrent calls that can be made over the SIP Line. The number of channels you can set is the maximum of SIP Trunk licences the system has. Also if you have more than one SIP Line these licences must be shared between the SIP Lines.

SIP URI Setting for Incoming DDI Calls.

  • Via is taken from the Use Network Topology Info setting on the Transport page.
  • Local URI is set to * (star) as wild card. This will send all incoming calls to the Incoming Call Route list.
  • Contact, Display Name and PAI all need to be set as shown.
  • Registration is selected form the drop down box and is the SIP Credentials settings.
  • Incoming and Outgoing Group should be set to the same number as the SIP Line number.
  • Max Calls per Channel is the amount of concurrent calls that can be made over the SIP Line. The number of channels you can set is the maximum of SIP Trunk licences the system has. Also if you have more than one SIP Line these licences must be shared between the SIP Lines.

Incoming Call Route

  • A Incoming Call Route for each DDI number needs to be created and its destination set.
  • Line Group ID settings is the same as the SIP Line/Incoming and Outgoing Group number.
  • Incoming Number is the DDI number entered in the E.164 format as shown +441234567890
  • Destination is set normal to ring a group, user, shortcode, voicemail or voicemail action.

BLF or Busy Lamp Field

What are Busy Lamp Fields or BLFs?

BLF or Busy Lamp Fields are typically a collection of indicators on a phone that show who is talking on other phones connected to the same PBX and typically used by a receptionist or secretary to aid in routing incoming calls.

To configure phone keys via the Hosted Platform simply do the following:

  1. Ensure the device is provisioned through VoiceHost (devices are listed in the portal under "provisioning"
  2. Find the device in the list you wish to configure the keys for.
  3. Select "Provision Keys"
  4. Select "BLF" from the drop-down and enter your account number followed by * and the extension you wish to see example 12345*204
  5. Save and reboot the phone ensuring that the checkbox for function keys is enabled.
Official Telephone Handset BLF Key Labeling Templates

You can download a formatted Key Labelling template for your Telephone Handsets below:

NOTE: These are pre-formatted to replace the paper BLF name inserts on your phone and should not be altered in size or scale.

VoiceHost Telephone handset BLF Key Labeling Templates
ManufacturerModel (click to download .doc .pdf)ModelModel
Snom3xx Series7xx Series720 | D725 | 760 | D765
CiscoSPA500S Attendant Console sidecars7861 
PolycomVVX Expansion Module   
YealinkSIP-T38G , SIP-T28P , SIP-T26P , IP Phone Expansion Module EXP38  
GrandstreamGXP 1628 | 1630  
PanasonicKX-UT133 | KX-UT136  
Softphone BLF Functionality

Under 'Quick Dial' add the contacts you wish to monitor using the method prescribed at the top of this page.

Detailed Softphone instructions can be found here: https://www.voicehost.co.uk/help/softphone

What are Busy Lamp Fields or BLFs?

BLF or Busy Lamp Fields are typically a collection of indicators on a phone that show who is talking on other phones connected to the same PBX and typically used by a receptionist or secretary to aid in routing incoming calls.

To configure phone keys via the Hosted Platform simply do the following:

  1. Ensure the device is provisioned through VoiceHost (devices are listed in the portal under "provisioning"
  2. Find the device in the list you wish to configure the keys for.
  3. Select "Provision Keys"
  4. Select "BLF" from the drop-down and enter your account number followed by * and the extension you wish to see example 12345*204
  5. Save and reboot the phone ensuring that the checkbox for function keys is enabled.

Panasonic NCP PBX - SIP Trunk Configuration Guide

How to configure SIP Trunking on a Panasonic NCP IP PBX

Tentative Version 0.1(PSN) 18th, July, 2013


SIP Trunk – Port Property:
Important Note: Programming the details of the SIP trunk is done in this field.
In this example, the system has been programmed to use the changed FAX setting and NAT Keep Alive ability.

- Reject T.38 Request change to “Enable”. (Default: Disable)
  *Note SIP server does not support T.38. (Need to set reject T.38 request by PBX.)

Recommended setting
- NAT - Keep Alive Packet Sending Ability change to “Enable”. (Default: Disable)
Go to 1.Configuration - 1.Slot and select “IPCMPR Virtual Slot”. and click “Ous”.
Move mouse over “V-SIPGW16” and click “Port Property”.


Main Tab:
1. Channel Attribute:                                 Basic Channel
2. Provider Name:                                     Enter a logical name
3. SIP Server Location – Name:                 Enter your assigned server as shown in the VoiceHost control panel.
4. SIP Server Location – IP Address:           Not required
5. SIP Server port Number:                        Leave at 5060
6. SIP Service Domain:                             Not required
7. Subscriber Number:                              Not required


Account Tab:
1. User name:
Enter the SIP Account (User name) as supplied by VoiceHost. Please note that this is just the SIP Account (user name) and DOES NOT include @FQDN For example: SIP Account (User name) = ST00000T000 Enter: ST00000T000

2. Authentication ID:                      
Enter the Authentication ID as supplied by VoiceHost. Please note that this is just the Authentication ID and DOES NOT include @FQDN For example: Authentication ID = ST00000T000 Enter: ST00000T000

3. Authentication Password:
Enter the Password as supplied by VoiceHost


Register Tab:
1. Register Ability:                                           Leave at Enable
2. Register Interval:                                        Leave at 3600
3. Un-Register Ability:                                     Leave enabled
4. Registrar Server – Name:                             Not required  * If SIP Server and Registrar Server are different, enter the Registrar Server.
5. Registrar Server – IP Address:                      Not required
6. Registrar Server port number:                      Leave at 5060

Go Back to “Slot”.
Move mouse over “V-SIPGW16” again, and click “Shelf Property”.
NAT - Keep Alive Packet Sending Ability:                   Change to Enable
NAT - Keep Alive Packet Type:                                 Confirm Blank UDP
NAT – Keep Alive Packet Sending Interval:                    Confirm 20

Then, click“OK”. Move mouse over“V-SIPGW16” again, and click “Ins”.


Incoming Call Routing:
Go to “10. CO & Incoming call” and select “3.DDI /DID Table
1. DDI/DID Number:                       Enter the DDI number in the format 44+PSTN Number (as below)

  • Example: PSTN number=0843-9999999
  • Enter: 448439999999 (Remove “0” of 0843-)

2. DDI/DID Name:                Determined by the installer (optional setting)
3. DDI/DID Destination:     Determined by the installer (extension number, group etc)
All other settings can be left at default


Outbound Call CLI:
Each extension that wishes to present an individual CLI needs to be programmed with a usable CLI. The usable CLI is a PSTN number assigned with the SIP trunk.

 i.e. if the PSTN number is 0843-9999999, the CLI to be programmed is 08439999999

Go to “Calling Party” tab.
1. From Header – User Part:         Change to PBX-CLIP

All other tabs may be left at default:
- Header Type
- From Header – SIP-URI (100 characters)
- P-Preferred-Identity Header – User Part
- P-Preferred-Identity Header – SIP-URI (100 characters)
- Number Format
- Remove Digit
- Additional Dial
- Anonymous format in “From” header
- P-Asserted-Identity header

Go to “4.Extension, 1.Wired Extension, 1.Extension Settings” & select “ISDN CLIP”

1.   Enter a valid CLI for each extension that requires it in the CLIP ID field. This setting, callee side shown ‘08439999999’.
2.   Enter the name for each extension that requires it in the Extension Name field

This setting, what characters shown callee side is now testing.


[T.38 Tab]

1. Reject T.38 Request from Network:      Change to Enable

All other tabs may be left at default
- T38 FAX Max Datagram
- T38 FAX UDPTL Error Correction - Redundancy
- T38 FAX UDPTL Redundancy count for T.30 messages
- T38 FAX UDPTL Redundancy count for data

Panasonic PBX NS1000 SIP Trunk Setup

This document is a reference for configuring “Voicehost” SIP trunks onto Panasonic NS1000 and includes the settings required for Incoming Call DDI routing and Outgoing Call CLI presentation

DOWNLOAD HERE

MITEL IP PBX SIP Trunk configuration

This document provides a reference to Mitel Authorized Solutions providers for configuring the Mitel 3300 ICP to connect to VoiceHost SIP trunks. The different devices can be configured in various configurations depending on your VoIP solution. This document covers a basic setup with the required option setup.

Interop History

VersionDateReasonDownload
1November 2013Initial Interop with Mitel 3300 6.0 SP1 and VoiceHostDownload the Mitel 3300 Interop Guide

Interop Status

The Interop of VoiceHost trunk line has been given a Certification status. This service provider or trunking device will be included in the SIP CoE Reference Guide. The status VoiceHost trunk line achieved is: COMPATIBLE

The most common certification which means VoiceHost SIP trunk has been tested and/or validated by the Mitel SIP CoE team.

Product support will provide all necessary support related to the interop, but issues unique or specific to the 3rd party will be referred to the 3rd party as appropriate.

Software & Hardware Setup

This was the test setup to generate a basic SIP call between VoiceHost trunk line and the 3300ICP.

ManufacturerVariantSoftware Version
Mitel3300ICP MXe12.0.1.24
MitelMinet sets:5340,5220,533005.02.01.07
MitelMBG - Teleworker8.0.12.0
MitelMBG - Gateway8.0.12.0

3CX - SIP Trunk Guide

System Preparation

Before configuring the SIP trunk it is required to go through the following checklist and make changes where necessary:

Further setup information can be found in our Academy:  3CX Academy Basic Course

3CX Version

Some providers gained support and compatibility with 3CX on a specific product version. It is advisable to always run the latest version of 3CX to ensure ongoing compatibility.

Minimum 3CX Version: 3CX Phone System 16.0

Provider Capabilities

Below is a short overview of the provider's capabilities and services and whether they’re supported or not:

  • CLNS (Clip No Screening): No
  • Catch All Routing: Yes
  • Fax in T38: Yes
  • CLIR (Number Suppression): Yes
  • DTMF via RFC 2833: Yes
  • Outbound Codec Order: G711A, G711U, G722, GSM, Opus
  • NAT Support: Yes
Configuring the Trunk with 3CX

The general instructions outlining how to add a new SIP Trunk to your 3CX installation can be found  here .

Adding the Trunk

Go to  “SIP Trunks”  and select  “Add SIP Trunk”

  • Select Country: UK
  • Select Provider in your Country: VoiceHost
  • Main trunk number: This will have been provided to you by VoiceHost. You must enter the number in the E164 number format (e.g. +44123456789)
  • Press OK

Under the  “General”  tab in the  “Authentication”  section, enter your Authentication ID and Password as well as the registrar address (these will be supplied to you by VoiceHost).

Adding Additional DIDs

To associate all other DIDs/Numbers you have in your VoiceHost account with 3CX, go to the Management Console → SIP Trunks, double-click on your VoiceHost Trunk and go to the  “DIDs”  tab

Here you should already see 1 entry; that is the Main Trunk number you have set. Add all other DIDs/Numbers you have to the list in the E164 number format (e.g. +44123456789) and press OK.

Creating Inbound Rules

Now that you have associated all your DIDs/Numbers with your SIP Trunk in 3CX, you can create Inbound Rules to set where calls will be routed when those numbers are called. Instructions on how to create Inbound Rules can be found  here .

Number Format
General

When configuring VoiceHost SIP Trunks in 3CX, all numbers should be entered in the E.164 number format (e.g. +44123456789), otherwise, call routing will fail.

Outbound Caller ID

VoiceHost trunks do not support Clip No Screening which means you can only present numbers that are associated with your account as Outbound Caller ID.

Outbound Rules

When configuring your Outbound Rules, numbers can be dialled in all valid number formats. More information about how to create Outbound Rules and how they work can be found here

Enabling TLS and SRTP

Under the 'General' tab please update the host to the one shown in the VoiceHost portal. This changes for TLS and SRTP so it will only be changed once enabled.
Under Options, please also upload the linked PEM under the option for the trunks 'TLS Root'.
Ensure SRTP is enabled.
Ensure TLS is set and the transport.
Ensure that host port is set to 'Auto-Detect'

Root Certificate: download here (You will need to rename to .pem)

Hosted Platform Short Codes

Cloud Platform Vertical Service Codes (Telephone Short Codes)
Action
Dial
Emergency Services999 or 112
Call a group of phones (as defined in the portal under call groups)*<group number>
Intercept/Pickup group call*0#<pickup group ID>
Intercept/Pickup extension call**<seat/extension number>
Call another extension (internal only)<seat/extension number>
Speaking clock (on-platform)123
Dial Welcome Message1234
Withhold number prefix (per call)141<telephone number>
Last Call Identified (DDI calls and Group calls only)1471
Record a custom prompt (e.g. IVR greeting, Queue greeting)151 (Record your prompt)
               |_   1 - Accept the recording
               |_2 - Listen back to the recorded prompt
               |_3 - Re-record the prompt
Call Monitoring (Call Whisper), listen into another seat and optionally whisper to them. (passwords defined in the portal)154, <seat number>,<password>
  |_1 - Listen to the call
  |_2 - Whisper to extension
Dial Echo Test (used for latency diagnostics)160
Time Profile Night Mode (Toggles Active/Inactive destination)*1#<time profile number>
Page extension (one-way audio)*2#<seat/extension number>
Page group (one-way audio)*3#<call group>
Intercom (two-way audio)*4#<seat/extension number>
Wake-up call reminder (Create and Delete)*5#<enter 24H time>
Call Parking1900 <parking reference read back> (Parks the current call)
<dial parking reference given when parking> (retrieves a given parked call)
Call Recording#1 (mute call recording)
#2 (unmute call recording)
Extension Call Intercept/Pickup**<seat number>
Dynamic Call Queue agent login (extensions jumping in/out of queues)120*<queue number> (Login to a call queue)
121*<queue number>  (Logout of a call queue)
Voicemail
Access Voicemail Externally (mailbox & password required from the portal)0843 557 4 557
Access Extension Voicemail (only accessible from the extension itself)1571
Access Shared Voicemail (accessible from any extension within the account)1572
Voicemail Menu0 - Mailbox options
               |_        1 - Record unavailable greeting (rings out)
               |_2 - Record busy greeting (only works if handset sends a busy signal back to platform, disable call waiting)
               |_3 - Record name
               |_4 - Record temporary greeting
               |_5 - Change mailbox password
1 - Listen to old messages (messages previously listened to)
2 - Change folders (Work, Friends, Family)
3 - Advanced options
               |_1 - Call back sender
               |_2 - Move message to another folder (Work, Friends, Family)
4 - Play the previous message (if exists)
5 - Repeat the current message
6 - Play the next message (if exists)
7 - Delete or Restore a recently deleted message
8 - Forward to another users extension
9 - Save Message
* - Help (Repeats the menu options)
# - Exit
Conferencing
Access Conferencing Service Externally0843 557 5 575
Call or transfer into the conferencing facility155, <room>#, <PIN or admin PIN>#, <state name>#
Conference Room Short Codes* - Conferencing Menu
               |_   1 - mute and unmute
               |_2 - Lock and unlock the room - admin only
               |_3 - Kick the last joined user - admin only
               |_4 and 6 - Conference room volume up/down
               |_7 and 9 - users volume up/down
               |_8 - Exit the conference